line pump
英 [laɪn pʌmp]
美 [laɪn pʌmp]
网络 中间泵; 管线泵
双语例句
- Advantages& Disadvantages and Selection of Cooling Bed in Steel-pipe Product Line coolant pump motor
钢管生产线上各种冷床的利弊与选用冷却泵电动机-机床 - Fault Analysis on the Abnormally Large Current on the Protection Zero Line of the Circulatory Pump Motor
循环泵电动机保护零线上反常大电流的故障分析 - According to flowing back problem at Hailaer exploration district, a method of unflowing to acquire production by using long steel line and hydraulic pump is discussed.
针对海拉尔探区中深井排液难的问题，探讨了利用长钢丝绳抽汲排液及水力泵排液求产方法。 - Well, it won't if there no line at the pump.
额，如果油泵没有输油管就不会。 - Instability line support, pump base, or anchor bolts loosening caused by vibration are common causes, the various fastening bolts must be to avoid loosening.
管路支撑不稳，水泵底座或地脚螺栓松动是造成振动常见的原因，必须紧固各处螺栓，避免出现松动。 - The difference press is maximum in the center line of pump, and the difference is minimum in the edge of pump.
泵腔中心线处的压强差最大，两侧处的压强差最小； - They bully into line at the gas pump ( Martin Gottfried)
他们在气泵前恶棍似地插队（马丁哥特弗莱德） - Remove low-pressure line for high-pressure pump at fuel line transfer point.
拆下燃油管路输送点处的高压泵低压管路。 - For example, one fabricator installed an oil trap in the line between the vacuum pump and chamber in a lyophilizer with an internal condenser.
例如有的制造商在真空泵和前箱间安装了有内部冷凝器的捕油器。 - Detach the vacuum line on the pump.
拆下泵上的真空管路。 - Improvement on Injection Characteristics of the Electronic In line Pump Pipe Valve Injector Diesel Injection System
电控PPVI柴油喷射系统喷射特性的改进 - Corrosion of Minimum Flow By-pass Line for High-pressure Lean Amine Pump
高压贫胺液泵最小流量线副线的腐蚀 - The operating condition point of centrifugal refers to the joint point of resistance curve of pipe line and characteristic curve of pump.
离心泵的工况点就是管道性能曲线与水泵性能曲线的交点，常采取更换叶轮或切削叶轮； - The test and analysis conclude that the cracking failure of minimum flow by-pass line of high-pressure lean amine pump in the hydrocracker are caused by sulfur stress corrosion and turbulent flow corrosion, which are aggravated by pipeline vibration.
经过检测分析认为加氢裂化装置高压贫胺液泵最小流量控制阀副线的腐蚀开裂原因是胺液和硫化氢的应力腐蚀和湍流腐蚀，管线振动加剧了腐蚀。 - Calculation the length of contact line for dry screw vacuum pump
干式螺杆真空泵接触线长度的计算 - Top Tube Construction of Link Line and Pump Station of Section Tunnel on No. 2 Line of Shanghai Metro
上海地铁二号线区间隧道的联络通道及泵站的顶管法施工 - Research on the Axial Force of the In-Line Magnetism Pump
管道式磁力泵轴向力研究 - The Design of Cam Profile for In line Fuel Injection Pump
喷油泵凸轮廓线设计 - The dynamic controlling of spreading stream line in pump CAD system
水泵CAD中的流线展开线动态调控机制 - Based on the equation of action line for cycloidal pump, a geometrical mathematical model is built to solve instantaneous flow, displacement, average flow and the pulsation of the pump.
根据摆线泵的啮合线方程，建立了用几何法求解摆线泵的瞬时流量、排量、流量脉动率的数学模型。 - The corrosion resistance of rubber used in flexible line pump
柔管泵用管材耐腐蚀性能的研究 - This paper is original from an item on technical innovation in Line Electric Pump Limited Corporation, which mostly researched the theory of water pump capability parameters testing, analyzed the errors, and built the measurement and control system.
本课题来源于安徽省莱恩电泵有限公司的一个技改项目，主要进行水泵性能参数测试的理论研究、误差分析以及测控系统的建立。 - The electronic in line pump pipe valve injector diesel injection system is a new solenoid controlled in line pump system.
分析了电控直列泵－管－阀－嘴（PPVI）柴油喷射系统的基本喷射特性。 - Practical Molded Line or the Roots Pump Rotor Calculated by Computer
电算法求罗茨泵转子实际型线 - The in-line debugging assembled injection pump
组合式喷油泵的现场调试 - The feasibility to cool component cooling water with refueling water storage tank through the containment spray test line, spray pump and spray heat exchanger in the event of loss of essential service water in nuclear power plant is analyzed.
针对核电厂在失去重要厂用水后，用换料水箱通过安全壳喷淋系统管线、喷淋泵和喷淋热交换器构成冷却回路，以反冷设备冷却水系统进行了分析。 - Research and Control of the Electromagnetic Actuator In line Fuel-injection Pump
直列式喷油泵中电磁执行器的研究与控制 - The Technology Study of Assembly Line for Micro Electric Pump
微型电泵装配流水线的技术研究 - Simulation results meet the desired objectives, in line with the Charge Pump Circuit design theory, and the design is the result of a combination of theory and practice.
仿真结果达到预期目标，符合电荷泵电路的设计理论，是理论和仿真实践相结合的结果。 - According to the angle between pump shaft and horizontal line, a pump system could be divided into three types, which are vertical pump system, slanting pump system and horizontal pump system, respectively.
根据泵轴轴线与水平线的夹角分，泵装置的类型有立式、斜式和卧式等三种基本装置型式。